Видео

Nice video, keep it up, thanks :)

I had a problem with shaky motor around 120 deg it would start going crazy. If you have this problem you can smooth out the movement with a capacitor wired in series with the POT. In my case 100 ųF capacitor worked great.

From where can I get the code?

tried adding include servo.h and it still said its not in my directory

Way too hard t understand. He doesnt even say wich pins to connect on ur arduino

Super helpful, Thanks!

works nicely

// Definisi pin untuk LED dan buzzer const int ledRed = 9; const int ledYellow = 10; const int ledGreen = 11; const int buzzer = 8; void setup() { // Set pin-mode untuk LED dan buzzer sebagai output pinMode(ledRed, OUTPUT); pinMode(ledYellow, OUTPUT); pinMode(ledGreen, OUTPUT); pinMode(buzzer, OUTPUT); } void loop() { // Mengatur LED merah untuk berkedip 3x for (int i = 0; i < 3; i++) { digitalWrite(ledRed, HIGH); tone(buzzer, 1000); // Bunyikan buzzer delay(500); // Tahan LED dan buzzer menyala selama 500ms digitalWrite(ledRed, LOW); noTone(buzzer); // Matikan buzzer delay(500); // Tahan LED mati selama 500ms } // Mengatur LED kuning untuk berkedip 3x for (int i = 0; i < 3; i++) { digitalWrite(ledYellow, HIGH); tone(buzzer, 1500); // Bunyikan buzzer delay(500); // Tahan LED dan buzzer menyala selama 500ms digitalWrite(ledYellow, LOW); noTone(buzzer); // Matikan buzzer delay(500); // Tahan LED mati selama 500ms } // Mengatur LED hijau untuk berkedip 3x for (int i = 0; i < 3; i++) { digitalWrite(ledGreen, HIGH); tone(buzzer, 2000); // Bunyikan buzzer delay(500); // Tahan LED dan buzzer menyala selama 500ms digitalWrite(ledGreen, LOW); noTone(buzzer); // Matikan buzzer delay(500); // Tahan LED mati selama 500ms } delay(1000); // Tahan 1 detik sebelum mengulang }

Why does only pin 13 work on my arudino?

YOOOOOO I ACTUALLY WORKS I SUBSCRIBING!!!!!🎉🎉🎉🎉🎉🎉🎉🎉🎉🎉😮😮😮😮😮

bro you said you where gonna link the code in the desc

nice vid but my arduino uno R3 ATMEGA328P (CH340G) has its 13 pin linked to the onboard LED so not the LED on the breadboard is blinking but the onboard led, of course i can just change the code to pins 12 11 and 10 and everything works. Great tutorial for me man

this is very well explained. i needed breakdown for my project of "robotic arm using servo and POT" and this provided me everything i needed to know. thanks!

#include <Servo.h> //accesses the Arduino Servo Library Servo myservo; // creates servo object to control a servo int val; // variable to read the value from the analog pin void setup() { myservo.attach(9); // ensures output to servo on pin 9 } void loop() { val= analogRead(1); val= map(val, 0, 1023, 0, 180); myservo.write(val); delay(15); // reads the value of the potentiometer from Al (value between 0 and 1023) // converts reading from potentiometer to an output value in degrees of rotation that the servo can understand // sets the servo position according to the input from the potentiometer // waits 15ms for the servo to get to set position }

I highly advise that you use the vertical stabilizer screws to tap out vertical stabilizer before installing. The screws are very hard to screw in with parts assembled. High probability you will strip out screw head if you don't tap out 1st.

Thank you so much for helping me 😇👌

finaly i can finish the led cock

idk why it isnt working :(

Exactly what I needed for my project! Thank you so much! Is there any way to make the LED's fade into each other rather than blink?

The project works for me, Thank you very much.

Nice presentation! Exactly what I need to know. thanks.

Its says "cant access sketch"

This is why i wish i was there, my blue and green came on -went off right away and finally got the red to work and it blink off and on. so is it post to happen like this.

Thank you so much for your tuturial sir ❤ we are already done with our activities this helps us very much💗

kindly share the block code

<3

she yle pedarasto iolad geqna prowo

Hello! Thank you for this clear tutorial! I want to ask you, is it possible to buy an arduino with more outputs, and change the code so on a chain of maybe 20 LEDs, the two outside LED's activate first, then the next two etc, until they meet in the middle, then reverse until they reach the outside pair again on loop? What would that code look like?

I am from Ghana 🇬🇭. Trying to learn Uno. I hope I am at the right place

Hi, Awsome video. How would I Add another potentiometer to this circut? So I can control one servo from two potentiometers. I have managed to get one servo opperating with one pot but not two. thanks for any feedback provided.

Nice tutorial, thank you 🥰

I have depount cables bit what color matches the green one

Can you do this in the small breadboard?

can you write the code for this project and not using the servo library but instead use micros and millis

Very Nice! Thx

There is no port option

IT WORKED!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! GIMME A HUG MY MAN

this is boring

would this work for multiple LEDs? For example, I am trying to make a circuit where the LEDs spell out "I <3 U" where the I turns on, the <3 turns on, and then the U turns on. How would I make sure that each LED is connected to its respective resistor?

Thanks for your guide😊

its going in reverse somebody please help

I like balls

Was a great one ❤

why does my servo motor just go crazy when i turn the potentiometer to the right?

Hi ah when i plug my jumper cable only 13 work ah 12 or 11 didnt turn on with the corresponding light when i put it the exact way you did it

just pulled mine out of the attic. Thank You for the refresher

Hello sir can I use different code to this connection?

Why is my first led brighter than all the others?

Very informative video, concise and to the point. Thank you for putting the video out.

Thank u so much